Fellow “Fly-Rotarians” –
I’ve got an “Atkins Special” –
85-86 13B, short intake manifold, 2 injector TMW Throttle body, MicroTech ECU, and Tracy’s EM2.
This weekend I finally was able to
put everything in place and try an engine start. I tried three tries cranking
the engine for about 15-30 seconds and it felt like it was firing every once
in a while but not enough to start. I took the intake off and started to take
the plugs out to see if there was a pool of gas in the rotors, when it felt
like one or both of the bottom plug wires weren’t fully seated. I re-seated
the plug wires and had my wife crank the engine while I watched the intake. Ah
ha! The rear (#2) rotor’s injector wasn’t firing. So, I moved the #2 injector
wires to the #1 rotor and cranked again and there was spraying – so it wasn’t
the wires and off with the fuel rail and out comes the #2 injector. I couldn’t
see any obvious clogging, so I cycled it a few times while dropping
penetrating oil into it (OK it just happened to be the handiest thing at the
moment). The penetrating oil started to go through the injector after a couple
cycles so I put it back in and buttoned up the fuel rail and reconnected
everything. I Cranked briefly again and there was now a spray pattern. So, it was time for another real try at
starting. I cranked for 10 seconds or so and ka-chug – Vrrrrooooommmmm
3500-4000 rpm with a
closed throttle! After 2 seconds of hysteria I turned the key to off and went
back (it’s a pusher) to see if there were any leaks or other anomalies.
I guess I really wasn’t expecting
it to start and my plan for what to look for on my engine monitors and ECU
went out the window when it took off like that! A brief inspection of the
engine, hoses, and wires turned up nothing out of the ordinary. So it was time to try again, this time
with a real expectation of a start and another plan on what to do in the first
few seconds. Again a few seconds of cranking and off she went. This time I
checked “OP” on the EM2 and it was reading 112psi – hmmm – a tad high but I
guess high is better than low. Fuel pressure was 61psi and RPMs were 3000-3500.
After 30 seconds I turned it off and went to re-check everything. Again
everything looked good except now that the oil had made to all the little
nooks and crannies I was about a quart low. So I added a quart, and checked
coolant levels and topped them off as well. I didn’t see any oil in the
plastic rotor oil “injection” lines so I decided, until I’m satisfied that
there is oil flowing, I was going to use 2-cycle oil. I added some 2 cycle and
sloshed the tank around by rocking the plane.
I read a little more in my ECU
(MicroTech) manual and turned off the cold start
enrichment and found the screen where the fuel flow at idle is set. I cranked it up again and began
fiddling with the idle fuel flow when the 2-cycle mix made it to the injectors
and things began to run rough and it died. I started it up again and it ran
rough for a few seconds and died again. And, that’s where I had to leave it
this weekend.
All in all I’m a happy
camper! I didn’t fully expect to
get the engine running quite so easily. So, now it’s a matter of figuring out
how to control the open time on the injectors so I can idle at something less
that 3000 RPM, and a whole bunch of fine tuning.
My airplane is now “whole”. All
the parts are there (well except the seat cushions). Now it’s just a small
matter of getting them all working together – the first time and every time,
for as long as I want them to!
Regards,
Joe
Hull
Redmond
(Seattle), Washington
Cozy MkIV #991
(working on Engine & Electrical & Finishing)
http://www.maddyhome.com/canardpages/pages/JoeHull/index.html