|
|
Christian,
I would like some pics as well if you wouldn’t
mind.
My address is bbradburry@verizon.net
Bill
From: Rotary motors in aircraft
[mailto:flyrotary@lancaironline.net]
Sent: Monday, October 17, 2016
7:10 AM
To: Rotary
motors in aircraft
Subject: [FlyRotary] Re: New
Gearbox and P-Port Renesis Update- for Neil Unger
Do you have a personal email as I can't seem to post to this forum with
pics
Cheers
Sent from my iPhone
What manifold pressure do you see at idle? I would love to see a
few pictures of your FWF.
Hi Bobby
I went for a single 90mm tb and plenum over the opposite side of the
motor and seems to work well, idles at approx 2150 and happily there.
Could get lower but prop speed is low enough.
Christian
On Monday, 17 October 2016, Bobby J. Hughes <flyrotary@lancaironline.net>
wrote:
Individual TB's were used so they could be located as close to the
block as possible for improved idle and throttle response. Idle is still at
18" MP cold and a little lower after warm up. The renesis should
have little or no overlap so the single throttle body before the intake
manifold appears to work well.
Sale is pending
for second buyer. Not sure if engine is staying with the plane or being
removed.
Bobby
Sent from my iPad
> On Oct 16, 2016, at 10:38 AM, Bill Bradburry <flyrotary@lancaironline.net>
wrote:
>
> Bobby,
> Do you know why he did the three TBs and not a plenum with one TB?
> Also I thought I saw where the sale of his plane was pending. What
is going on there? Was it sold as a flying plane or did you remove the
engine?
> Bill
>
> -----Original Message-----
> From: Rotary motors in aircraft
[mailto:flyrotary@lancaironline.net]
> Sent: Sunday, October 16, 2016 8:50 AM
> To: Rotary motors in aircraft
> Subject: [FlyRotary] Re: New Gearbox and P-Port Renesis Update- for Neil
Unger
>
> Mark Steitle experienced sticky slide throttle. He modified it several
times and eventually switched to one butterfly TB per rotor.
>
> Bobby
>
> Sent from my iPad
>
>> On Oct 16, 2016, at 3:50 AM, Neil Unger <flyrotary@lancaironline.net>
wrote:
>>
>> Doug, Had severe problems with a slide throttle, went with
butterfly and no problems since. Neil.
>>
>>
>>> On 10/16/2016 7:07 PM, Doug Lomheim wrote:
>>> Hi Neil:
>>>
>>> I have read where some P-Port attempts have resulted in a
“sticky†throttle due to suction at certain power applications,
etc. Do you experience any issues such as that with your set up?
>>>
>>> thx.
>>>
>>> Doug
>>>
>>> --
>>> Homepage: http://www.flyrotary.com/
>>> Archive and UnSub: http://mail.lancaironline.net:81/lists/flyrotary/List.html
>>
>>
>> --
>> Homepage: http://www.flyrotary.com/
>> Archive and UnSub: http://mail.lancaironline.net:81/lists/flyrotary/List.html
>
> --
> Homepage: http://www.flyrotary.com/
> Archive and UnSub: http://mail.lancaironline.net:81/lists/flyrotary/List.html
>
>
> --
> Homepage: http://www.flyrotary.com/
> Archive and UnSub: http://mail.lancaironline.net:81/lists/flyrotary/List.html
--
Homepage: http://www.flyrotary.com/
Archive and UnSub: http://mail.lancaironline.net:81/lists/flyrotary/List.html
|
|