Probably because the EC3 already have a
1K resistor on the board to ground. So with the 18K in series you
have a 18:1 attenuation.
I questioned Tracy about adding the 1K resistor (in addition to
the two zeners) but he told me to do it. That's now 500 ohms
across the output from the CAS sensor.
There's already a pretty elaborate signal conditioning circuit on
the EC3 board.
I guess in the end it's all about getting a reliable clean timing
signal to the CPU interrupt input. I suspect the CAS output
voltage varies significantly with RPM.
Undoubtedly there are many different circuits that could
accomplish that. Some better than others for specific non-factory
installations.
Finn
On 6/23/2020 7:16 AM, Bobby J. Hughes
bhughes@qnsi.net wrote:
Dennis
H. and I used that circuit with the EC2. It’s external in the
wiring near the EC2 connector. It’s not compatible with the EC3.
Engine would not start.
Bobby
Sent from my iPad
> On Jun 22, 2020, at 9:00 PM, Stephen Izett stephen.izett@gmail.com
<flyrotary@lancaironline.net> wrote:
>
> I had this circuit from somewhere
> <Renesis CAS Zener Circuit.pdf>
>
> Steve Izett
>
>> On 23 Jun 2020, at 9:22 am, Finn Lassen finn.lassen@verizon.net
<flyrotary@lancaironline.net> wrote:
>>
>> Just for the record.
>> <ommkelgblomchfkc.jpg>
>> The 1K resistor and the two 2.7V zener diodes are the CAS
input clamping circuit.
>>
>> The rest is for redundant +5V to control panel (mixture
voltage being the critical one).
>> Vcc3 is J2 pin1 (+5V to control panel).
>> I just used BAX16 diodes because I had them. Any 100mA
(16V reverse voltage or more) diode will do.
>> LM78L05 flat side down. Left pin is output. Center pin is
ground and right pin is input.
>>
>> <jjfkkebmdbnhneko.jpg>
>> If you want to secure components against vibration make
sure you use Natural Cure Sealant (non -acidic)!
>> I'm using Dowsil 737 RTV sealant.
>> The auto parts store RTV is acidic and you don't want
your circuit board damaged (etched) by that.
>>
>> Finn
>>
>>> On 6/17/2020 6:57 PM, Finn Lassen finn.lassen@verizon.net
wrote:
>>> In addition to the CAS input clamping circuit, Tracy
also recommends shorting pins 1 and 3 of D18. The voltage drop
across the diode to the PCM module causes slightly lower mixture
and program voltage than the software was programmed for.
>>>
>>> However, if you are powering A and B controllers
separately (e.g. separate fuses or busses), I have a better idea.
>>> 1) Remove the D18 diodes (just below C45 which they
feed).
>>> 2) Add a LM78L05 (or similar) voltage regulator.
After each (A and B) of the power (L1 and L2) input coils (+ on
the big C20 and C21 capacitors) feed the input of the LM78L05 with
a diode. Output of it goes to J2 pin 2 (or + on C45).
>>>
>>> Same principle as powering the PCM from either of the
5V regulators on the EC3 board, but the 0.7V diode drop now
happens before the regulator, not after the 5V.
>>>
>>> CAS input clamping circuit:
>>> 1) A 1K resistor between J2-5 and J2-15 (CAS input
and ground).
>>> 2) Two 2.7V zener diodes in series, arrows or striped
ends (anodes) connected together. The non-striped ends (cathodes)
to J2-5 and J2-15 respectively (CAS input and ground). (Basically
in parallel with the 1K resistor). If you got the polarity of the
zener diodes correct you should see the signal from the CAS sensor
clamped to no more than 0.7 + 2.7 = +-3.4 volts on an
oscilloscope.
>>>
>>> I now have two bad chips (does not respond to reading
or programming attempts -- do "work" in the EC3). The chip pins
used to program the chip go to the Mode switch on the PCM. J2 pins
22 and 24. One might consider protection diodes for those pins.
Oddly the pins continue working for Mode switch input, just not
for re-programming the chip.
>>>
>>> The EC3 board was designed for in-circuit chip
re-programming (set mode switch to zero or disconnect J2).
Vpp/MasterClear are on J2 pin 11 (for A) and pin 1 (for B). PGC on
pin 22 and PGD on pin 24. However, Tracy found that the combined
capacitance of the programming pins of two chips made in circuit
programming unreliable. I wonder if it might work if one could
control the speed with which it communicates with the chip?
>>>
>>> Finn
>>>
>>>
>>> --
>>> Homepage: http://www.flyrotary.com/
>>> Archive and UnSub: http://mail.lancaironline.net:81/lists/flyrotary/List.html
>>>
>>
>>
>
> --
> Homepage: http://www.flyrotary.com
> Archive and UnSub: http://mail.lancaironline.net:81/lists/flyrotary/List.html
Disclaimer
The
information contained in this communication from the sender is
confidential. It is intended solely for use by the recipient and
others authorized to receive it. If you are not the recipient,
you are hereby notified that any disclosure, copying,
distribution or taking action in relation of the contents of
this information is strictly prohibited and may be unlawful.
This email has been scanned for viruses and malware, and may
have been automatically archived by Mimecast Ltd, an
innovator in Software as a Service (SaaS) for business.
Providing a safer and more useful place for your
human generated data. Specializing in; Security, archiving and
compliance. To find out more Click Here.