Received-SPF: none
 receiver=logan.com; client-ip=165.166.0.27; envelope-from=Jewen@Comporium.net
Date: Mon, 13 Jun 2005 22:30:56 -0400
From: Joe Ewen <Jewen@Comporium.net>
Subject: Re: [FlyRotary] Re: Air Horns
To: Rotary motors in aircraft <flyrotary@lancaironline.net>
Message-id: <015b01c57089$1800c020$6532a8c0@engineer1>
MIME-version: 1.0
Content-type: text/plain; charset=iso-8859-1
Content-transfer-encoding: 7bit
References: <list-1001145@logan.com>

Jerry,
Thanks, that looks good.  Do you have a contact for Ed?
Joe

----- Original Message ----- 
From: "Jerry Hey" <jerryhey@earthlink.net>
To: "Rotary motors in aircraft" <flyrotary@lancaironline.net>
Sent: Monday, June 13, 2005 9:28 PM
Subject: [FlyRotary] Re: Air Horns


> Joe,  if you bore a length of aluminum 1.375 (turn the o.d. as well)
> and then anneal it, the bell shape  can be pressed in.  Ed Klepeis can
> do it for  you.  Here is a pic of mine.  Ed would probably like to
> specify the aluminum grade.     Jerry
>


----------------------------------------------------------------------------
----


>
>
>
>
>
>
>
>
>
>
>
> On Monday, June 13, 2005, at 06:47 PM, Joe Ewen wrote:
>
> > Ben,
> > Thanks for the info.  I have look at TWM.  I am looking for air horns
> > for a
> > 1.375 (35mm) tube, but the smallest I could find was 40mm.  I am
> > working on
> > my intake for a 4 port Renesis as well.  I am interested in what other
> > people are doing on a Renesis intake, if you would care to share.
> > Attached
> > is an adapter block I drew for the secondaries, runner tube into one
> > side
> > and the other is sized to fit either a 195500-2020 (550cc) injector or
> > a
> > Renesis injector.
> > Thanks,
> > Joe
> >
> >
> > ----- Original Message -----
> > From: "Ben Schneider" <plumberben@yahoo.com>
> > To: "Rotary motors in aircraft" <flyrotary@lancaironline.net>
> > Sent: Saturday, June 11, 2005 8:56 AM
> > Subject: [FlyRotary] Re: Air Horns
> >
> >
> >> Joe,
> >>
> >>    Check out TWM induction. They are a little pricey, but the
> >> spinnings
> >> are very nice. They have them in many different sizes, and as
> >> spinnings,
> >> or they will make them to fit various carbs an throttle bodies. Most
> >> of us
> >> would likely use just a spinning. That is what I have.
> >>
> >>     Ben Schneider
> >>      RV7 Renesis 4 port(building intake manifold)
> >>
> >>>>  Homepage:  http://www.flyrotary.com/
> >>>>  Archive:   http://lancaironline.net/lists/flyrotary/List.html
> >>
> > <IntakeAdapter.pdf> Homepage:  http://www.flyrotary.com/
> >>>  Archive:   http://lancaironline.net/lists/flyrotary/List.html
>


----------------------------------------------------------------------------
----


> >>  Homepage:  http://www.flyrotary.com/
> >>  Archive:   http://lancaironline.net/lists/flyrotary/List.html
>