Actually, Mark,  I did not notice any variance in the cooling system from
the normal.  I just checked my flight log for that trip and at cruise my oil
and coolant ranged from 160-170F which is normal.  I too  would have thought
that as loose as the belts were (I could easily turn the water pump against
the belt friction by hand) that the water pump would have slowed down
sufficiently to have elevated the coolant temp.  But, it apparently did not.

Perhaps another way of looking at it is in regards to the power needed to
drive sufficient coolant, apparently not very much which corresponds well
with the 1/3 - 1/2 HP of the EWPs.

Ed
.
Ed Anderson
RV-6A N494BW Rotary Powered
Matthews, NC
----- Original Message -----
From: "Mark Steitle" <msteitle@mail.utexas.edu>
To: "Rotary motors in aircraft" <flyrotary@lancaironline.net>
Sent: Wednesday, May 05, 2004 8:57 AM
Subject: [FlyRotary] Re: Coolant Pressure Gauge


> Ed,
> You reported a loose alternator/water pump belt(s) while on your way back
> from SNF causing the alternator field breaker to trip.  Did you notice any
> changes in water pressure that could be associated with the loose
> alternator belts?
>
> Mark S.
>
>
> At 08:09 AM 5/5/2004 -0400, you wrote:
> >Steve,
> >
> >     I use a 0-30 psi fuel pressure sensor and gauge for my coolant
pressure
> >sensor and its still working fine after close to 300 hours.  At one time
> >(and they may still do) UMA offered a coolant (or water) pressure gauge
so
> >marked - they actually silk screened a new placard and placed it in the
fuel
> >gauge I purchased from them.  So my fuel gauge actually says "Water
> >Pressure"
> >
> >    The coolant gauge gives you pressure information that you soon begin
to
> >correlate with your coolant temperature as well as OAT.  You soon begin
to
> >notice when anything departs from the norm.  Its simple another bit of
> >information about your system which does nothing for you most of the time
> >but provide that comfort level that things are nominal - but, can alert
you
> >to departures from the nominal which bear investigating.
> >
> >
> >Ed
> >
> >Ed Anderson
> >RV-6A N494BW Rotary Powered
> >Matthews, NC
> >----- Original Message -----
> >From: "Steve Brooks" <steve@tsisp.com>
> >To: "Rotary motors in aircraft" <flyrotary@lancaironline.net>
> >Sent: Wednesday, May 05, 2004 7:18 AM
> >Subject: [FlyRotary] Re: Mystery of the leaking coolant
> >
> >
> > > Yes, it does sound like a good idea.  I've looked for a sender and
gauge,
> > > but haven't found any.  Does anyone have a good source for these ?
> > >
> > > Steve Brooks
> > >
> > > -----Original Message-----
> > > From: Rotary motors in aircraft [mailto:flyrotary@lancaironline.net]On
> > > Behalf Of Bill Dube
> > > Sent: Tuesday, May 04, 2004 9:04 PM
> > > To: Rotary motors in aircraft
> > > Subject: [FlyRotary] Re: Mystery of the leaking coolant
> > >
> > >
> > >
> > > >
> > > >With the overflow plugged it was probably building up some pretty
good
> > > >pressure, which I'm sure led to the failure of the pump seal.  It is
such
> > > an
> > > >odd thing to have happened, but I'm glad that my days of chasing the
> >drips
> > > >of coolant are over.  I think that the hoses must be there to stay,
since
> > > >they didn't blow off.
> > >
> > >          In "The Book" Tracy strongly suggests installing a coolant
system
> > > pressure gauge. It sounds like it might be a good suggestion, in light
of
> > > the trouble you had.
> > >
> > >
> > >
> > > >>  Homepage:  http://www.flyrotary.com/
> > > >>  Archive:   http://lancaironline.net/lists/flyrotary/List.html
> > >
> > >
> > > >>  Homepage:  http://www.flyrotary.com/
> > > >>  Archive:   http://lancaironline.net/lists/flyrotary/List.html
> > >
> >
> >
> >
> > >>  Homepage:  http://www.flyrotary.com/
> > >>  Archive:   http://lancaironline.net/lists/flyrotary/List.html
>
>
> >>  Homepage:  http://www.flyrotary.com/
> >>  Archive:   http://lancaironline.net/lists/flyrotary/List.html