Mailing List flyrotary@lancaironline.net Message #66762
From: Matt Boiteau mattboiteau@gmail.com <flyrotary@lancaironline.net>
Subject: Re: [FlyRotary] Re: PSRU thrust bearing/washer
Date: Thu, 29 Apr 2021 10:13:22 -0400
To: Rotary motors in aircraft <flyrotary@lancaironline.net>
From what I've talked with Neil about, it sounds like it's just a flat washer. (round stock on lathe). I'll find it easier cutting it out of a flat sheet though
One of my last flights, high speed cruise

Oil pan 228F
Oil rad 210F
PSRU 212F

I have a leaf blower and digital magnetometer, will work on ducting the oil cooler better next. Will need some turning vanes.

- Matt Boiteau


On Thu, Apr 29, 2021 at 9:04 AM Bobby Hughes BHughes@qnsinc.net <flyrotary@lancaironline.net> wrote:

Matt,

 

I know of one person on the list that made a new snubber from round stock on a lathe. Was the PSRU designed for a flat snubber or chamfered? What is your oil exit temperature?

 

Bobby

 

From: Rotary motors in aircraft [mailto:flyrotary@lancaironline.net]
Sent: Wednesday, April 28, 2021 10:23 PM
To: Rotary motors in aircraft
Subject: [FlyRotary] Re: PSRU thrust bearing/washer

 

Straight PTFE has a Durometer 50D-65D. I'll go with it.

https://www.mcmaster.com/9266K82/

Prop I have is a 74" ground adjustable Sensenich. Pitched to 22degrees. Static full power is 2200 while flying is 2600. With the 3.17 gearing, engine RPM is 8250.

Finn, I'm not sure, the restrictor is part of the fitting. Neil, can you pipe in here? I won't say I know anything like Tracy and them do, but a planetary gear, doesn't it only need a splash of oil for lub?

- Matt Boiteau

 

 

On Wed, Apr 28, 2021 at 7:38 PM Charlie England ceengland7@gmail.com <flyrotary@lancaironline.net> wrote:

Does 'glass filled' mean fiberglass? Any abrasive risk if the PTFE does start to wear? Looks like they also have straight PTFE sheet stock, but I didn't look at durometer.

Are you running some monster 8' diameter prop with that ratio?

Charlie

On 4/28/2021 5:46 PM, Matt Boiteau mattboiteau@gmail.com wrote:

Squished / deformed is the verbage I used back in 2019 about it. I can't seem to find any pictures on it, but I remember it being deformed up pretty good. I've been battling issues in the past with the vulcanization rubber of Neil's cushion drive was coming apart. I've put on Tracey's Cushion drive in the meanwhile.

Dry fitting everything (no oring and no snubber) with the input shaft sitting all the way down on the prop shaft, I have 0.085" clearance. To get the 5-10thou gap, I would need a snubber 0.075" - 0.080" thick. The closest I can get is 1/16" thick, which is 0.0625.

 

I found this stuff for the snubber, high temp. Can cut out a washer from it. 
https://www.mcmaster.com/8636K11/

 

There is a restrictor in the fitting going into the PSRU. I have a temp gauge on the PSRU, and it stays consistent with the oil. I have parts to add a PSI sensor to the back half of the PSRU to see if things are draining okay.


- Matt Boiteau

 

 

On Wed, Apr 28, 2021 at 5:29 PM Charlie England ceengland7@gmail.com <flyrotary@lancaironline.net> wrote:

The confusing thing to me is how it got hot enough to melt nylon; over 400 degrees F. That seems a lot hotter than than the shaft or bearings should ever get. 

 

Image removed by sender.

Virus-free. www.avast.com

 

On Wed, Apr 28, 2021 at 3:13 PM Matt Boiteau mattboiteau@gmail.com <flyrotary@lancaironline.net> wrote:

The end play was good. Metal ruler across and could just see daylight across.

 

Neil's uses a rubber oring, so we test endplay without it. Then adding the oring will add the nessessary clearance in end play.

 

The one Neil supplied was either nylon or Teflon flat washer and it melted, so removed it. So talking with him, switched it out to the oil embedded one. Again, just a flat washer.

 

Anyone have more details what Tracey used? Like a spring washer made out of nylon?

 

 

 

 

On Wed., Apr. 28, 2021, 14:16 Finn Lassen finn.lassen@verizon.net, <flyrotary@lancaironline.net> wrote:

Too little or too much end play?

Tracy specifies 0.005 to 0.035"

Note that if you check it without RTV, it may increase when you assemble it.

Finn

On 4/28/2021 1:05 PM, Matt Boiteau mattboiteau@gmail.com wrote:

I have one of Neil's 3.17 psru with Tracey's cushion drive. *I also sent Neil an email but it's late in the night in Australia.

 

After my fly off hours, tearing down the plane to inspect everything. The Ultra-Low-Friction Oil-Embedded Thrust Bearing is broken into pieces. 

https://wwwmcmaster.com/7421K28/

The nylon or teflon washer supplied just melted. I thought I nailed it with a fix using the oil-embedded, but I guess not.

I think in Tracey's documentation, he called it a snubber ? Any ideas what I can use, or why this happens?

- Matt Boiteau

 

--
Homepage:  http://www.flyrotary.com/
Archive and UnSub:   http://mail.lancaironline.net:81/lists/flyrotary/List.html

 


Image removed by sender. Avast logo

This email has been checked for viruses by Avast antivirus software.
www.avast.com



 



Disclaimer

The information contained in this communication from the sender is confidential. It is intended solely for use by the recipient and others authorized to receive it. If you are not the recipient, you are hereby notified that any disclosure, copying, distribution or taking action in relation of the contents of this information is strictly prohibited and may be unlawful.

This email has been scanned for viruses and malware, and may have been automatically archived by Mimecast Ltd, an innovator in Software as a Service (SaaS) for business. Providing a safer and more useful place for your human generated data. Specializing in; Security, archiving and compliance. To find out more Click Here.

Image
~WRD359.jpg
Image
image001.jpg
Subscribe (FEED) Subscribe (DIGEST) Subscribe (INDEX) Unsubscribe Mail to Listmaster