|
Thanks Ed.
My rotors (and e-shaft) are not new but were within spec. All housing/enclosure were new
Sent from my iPhone 4
Chris,
One thing you might check - is your coolant "O" rings - if they are compromised - combustion pressures can push mixture into your coolant system during compression stoke lowering your chamber pressure. That could show up as bubbles
in the coolant or you might notice "oily" sheen on top of your coolant if you can see it through your cap. You won't always get green coolant fluid in your combustion chamber if an O ring is compromised.
The O ring can seal on the intake stroke because at most you have a 14psi difference, but may not on the compression stroke where you can have a 100 psi difference between coolant pressure (ambient) and chamber pressure which could
push past a compromised "O" ring.
Also, if you take you engine down - check carefully in the coolant "O" ring lans to make certain there are no cracks. I use a dentist pick (a needle would probably work) and gentle pull it around the inside corners - if it catches,
examine that area closely.
Another thing you want to check is your rotors apex seal slots. They can wallow out through use (although you should not have that much use) such that the apex seals do not ride vertically in the slot and sort of lean over (as the supporting
wall of the slot wallows out) and do not seal as well as they should. I think Lynn suggested sticking an apex seal in the slot (one end) and with the other end sticking 3" or so in the air - measure how much you can measure by wiggling that end from one side
of the slot to the other. The far end of the apex seal should not move more than 3/8".
With new Rotors that again should not be a problem, but you are looking for stretches and this is one {:>)
Yes, it gets easier to pull and tear down an engine with practice - but, it gets to be less fun each time {:>)
Ed
Sent: Monday, February 14, 2011 10:39 AM
Subject: [FlyRotary] Re: Low compression in rotor 2 ... still
Not sure how that would effect the lower compression though.
Jeff,
I shall give that a try
Chris
From: Rotary motors in aircraft [flyrotary@lancaironline.net] on behalf of Jeff Whaley [jwhaley@datacast.com]
Sent: Monday, February 14, 2011 9:28 AM
To: Rotary motors in aircraft
Subject: [FlyRotary] Re: Low compression in rotor 2 ... still
Chris, try changing your spark plugs. If you’ve caused damage to the rotor springs from detonation, you’ve also exposed the plugs to the same force.
I have never had a problem starting my engine except for this past weekend … wouldn’t start, I was blaming it on the cold, so it got more pre-heat and eventually started exactly as you said, a lot of cranking and liking the starter assist.
Yesterday, same thing wouldn’t start – more pre-heat, still no joy. Pulled the plugs and they were coated with black soot, so I went home, got a brand new set of plugs – engine started right away and with no additional pre-heat.
Jeff Whaley
|
|
|
To remind y'all, following very hard starting, I discovered bad apex seal springs in my rotor 2 most likely due to detonation. I cracked the keg and replaced the rear apex
springs and sealed it all back up. While apart, I did not discover any damage other than the bad springs.
I have been trying to tune the engine, however, even using BOTH my EC2's, I am still having problems with very hard starting. When I do get it to start it is at full lean
and I believe only if I switch over to B. Once started I can take the mixture from full lean to a more moderate setting (even if the tuning is still lacking) and it will run on A or B about the same. I have reset A to factory settings. I do have a bit larger
injectors, per Mistrals recommendation, but did crank her up to 22. MAP and adjust Mode 3 once started to just over the mid point per the EC2 manual.
It takes an extended period of time of cranking (maybe 50 or 60 seconds...betting my starter is hating me) before it starts and then kinda just starts running as a continuation
of the starter being turned, instead of the engine actually "firing up".
I pulled the plugs to check inside and unlike before all the apex seals are nice and springy, HOWEVER, when I do a compression check I am only getting about 60 psi on the
rear rotor. I am getting about 80 psi on the front rotor, which is what I expected.
|
__________ Information from ESET NOD32 Antivirus, version of virus signature database 5873 (20110214) __________
The message was checked by ESET NOD32 Antivirus.
http://www.eset.com
This message, and the documents attached hereto, is intended only for the addressee and may contain privileged or confidential information. Any unauthorized disclosure is strictly prohibited. If you have received this
message in error, please notify us immediately so that we may correct our internal records. Please then delete the original message. Thank you.
image001.gif
image002.gif
|