Received-SPF: pass
 receiver=logan.com; client-ip=209.85.221.192; envelope-from=cozy4pilot@gmail.com
DomainKey-Signature: a=rsa-sha1; c=nofws;
        d=gmail.com; s=gamma;
        h=message-id:date:from:user-agent:mime-version:to:subject:references
         :in-reply-to:content-type:content-transfer-encoding;
        b=OvjpY/Q6ANDeGFWsEGzEZvIAo8oGumaPfMSrYTMe5n90zzbyJLgL0cBYMD64KGtRFP
         ryUcQnO1dQz62YndQYJL+Wy/Dw9sicCzQjVtEULOeNPOuamRsQ7Cha5qH5mMCzhSTc/H
         PHDOPWT/Jk8m/u/7pG6qczmkafogT3QDbYcYw=
Message-ID: <4AF6BADC.9040804@gmail.com>
Date: Sun, 08 Nov 2009 07:34:36 -0500
From: Steve Brooks <cozy4pilot@gmail.com>
User-Agent: Thunderbird 2.0.0.23 (Windows/20090812)
MIME-Version: 1.0
To: Rotary motors in aircraft <flyrotary@lancaironline.net>
Subject: Re: [FlyRotary] Battery Location[FlyRotary] Re: No start after engine
 replacement
References: <list-3960765@logan.com>
In-Reply-To: <list-3960765@logan.com>
Content-Type: text/plain; charset=ISO-8859-1; format=flowed
Content-Transfer-Encoding: 7bit

Ed,
That sounds like a good explanation for what I am seeing.  The battery 
is about two years old.  It is an Odyssey PC680.  I have two batteries, 
one sits on the rear spar and runs all of the engine stuff, and the 
other one is in the nose an runs the avionics.  I have pretty heavy 
cables running from the battery to the engine, 0 gauge as I recall, and 
they are not very long.  Maybe 5 ft for the one hooked to the started, 
and 3 ft for the one ground connected to the engine block.

I will check the voltage as you suggested while cranking,  I also have 
an emergency bypass switch where I cant power the engine critical buss 
from the front battery, so that would also be a quick test, as I could 
crank from the rear battery and power the EC-2 and coils from the front.

I just installed the EC-3, so I'm not too familiar with it yet.  I will 
see if it shows the RPM during cranking.  I'm not sure if it does or not.

Steve

Ed Anderson wrote:
> Steve, where is your battery located?  Engine compartment or nose??
> Long leads can drop a lot of voltage under cranking current.  New engine may
> have  higher compression and  may take more juice than previous engine to
> turn it over fast enough.  The fact that your old engine was also hard to
> start makes me wonder.
>
> Ed
>
> Ed Anderson
>
> Rv-6A N494BW Rotary Powered
>
> Matthews, NC
>
> eanderson@carolina.rr.com
>
> http://www.andersonee.com
>
> http://www.dmack.net/mazda/index.html
>
> http://www.flyrotary.com/
>
> http://members.cox.net/rogersda/rotary/configs.htm#N494BW
>
> http://www.rotaryaviation.com/Rotorhead%20Truth.htm
>
> -----Original Message-----
> From: Rotary motors in aircraft [mailto:flyrotary@lancaironline.net] On
> Behalf Of Steve Brooks
> Sent: Saturday, November 07, 2009 4:46 PM
> To: Rotary motors in aircraft
> Subject: [FlyRotary] Re: No start after engine replacement
>
> That's interesting.  I had not made any changes to mode 8, but it is 
> certainly easy enough to reset it to default. 
>
> Steve
>
> Steven W. Boese wrote:
>   
>> Steve,
>>
>> It might be useful to reset the EC2 timing mode 8 setting to the default
>>     
> setting. My EC2's do not produce consistent or strong sparks at RPM's  less
> than about 1200 if the EC2 timing is advanced using mode 8.  The greater the
> advance, the weaker the spark.  Occasionally there will be a strong spark,
> but the timing on these is very retarded.  With my EC2's, the most
> consistent low RPM sparks are obtained at the most retarded mode 8 setting,
> but the EC2 must be receiving CAS signals (engine running) in order to make
> this change.
>   
>> Steve Boese
>>
>> ________________________________________
>> From: Rotary motors in aircraft [flyrotary@lancaironline.net] On Behalf Of
>>     
> Steve Brooks [cozy4pilot@gmail.com]
>   
>> Sent: Saturday, November 07, 2009 1:09 PM
>> To: Rotary motors in aircraft
>> Subject: [FlyRotary] No start after engine replacement
>>
>> I replaced my original engine with another newly rebuilt block, and also
>> added the EM-3 to the installation. The old engine was hard to start,
>> and was also making a ticking noise when it did start, which didn't used
>> to be there.
>>
>> After several failed attempts, and double checking the connections, I
>> had a neighbor help me do some testing.  While the ignition test runs
>> fine, when checking one of the plugs, it sparks when I initially crank
>> the engine, and then stops.  Once in a while there will be another
>> spark, but not very often.
>>
>> I reinstalled the original CAS and have the same issue.  I have double
>> checked the CAS connections and checked them with an ohm meter to the
>> connector on the EC-2 also. Everything seems to check out, yet I get
>> only that initial spark. I have replaced the spark plugs with new ones,
>> and whenever I pull one to check it, is is wet with fuel, which is no
>> surprise.
>>
>> I am wondering if anyone has seen this type of problem, or if you have
>> any suggestions.
>>
>> Regards,
>> Steve Brooks
>> Cozy MKIV 13B turbo
>>
>> --
>> Homepage:  http://www.flyrotary.com/
>> Archive and UnSub:
>>     
> http://mail.lancaironline.net:81/lists/flyrotary/List.html
>   
>> --
>> Homepage:  http://www.flyrotary.com/
>> Archive and UnSub:
>>     
> http://mail.lancaironline.net:81/lists/flyrotary/List.html
>   
>>   
>>     
>
>
> --
> Homepage:  http://www.flyrotary.com/
> Archive and UnSub:
> http://mail.lancaironline.net:81/lists/flyrotary/List.html
>
> __________ Information from ESET NOD32 Antivirus, version of virus signature
> database 3267 (20080714) __________
>
> The message was checked by ESET NOD32 Antivirus.
>
> http://www.eset.com
>
>  
>
> __________ Information from ESET NOD32 Antivirus, version of virus signature
> database 3267 (20080714) __________
>
> The message was checked by ESET NOD32 Antivirus.
>
> http://www.eset.com
>  
>
>
> --
> Homepage:  http://www.flyrotary.com/
> Archive and UnSub:   http://mail.lancaironline.net:81/lists/flyrotary/List.html
>
>