28?

Anyway, thank you all for your replies. Sounds like a 150 psi sensor will be the safest.

I have no plans to tear down the supposedly brand new Renesis, so for now no modifications.

Thinking about a before cooler pressure sensor too. I suppose the only (easy) option is to drill and tap the oil metering pump supply hole (which I've already plugged)?

I would like to also have a before oil cooler temperature sensor. I guess I need to find a spot in the oil pan?

I suppose a 30 psi sensor is adequate for water pressure (assuming I don't go with Evans non-pressurized system)?

Trying to source sensors, I looked in the places I had purchased them decades ago (Newark, DigiKey, Allied) and was dismayed at the availability and prices. In my original RV-3 I had used the solid state MPX-5999 with barb from NXP USA.

A Google search finally lead me to a posting which led me to Aircraft Spruce and a "Swift" pressure sensor. That led me to eBay where there now is a wide selection of 5V (amplified) solid state sensors with 1/8-27NPT housings.

These solid state sensors have (amplified) output voltages from 0.5 to 4.5 volts with a 5 volt supply (they even come in 12V (10-25V) supply version for a bit more).
Yes, your engine monitor has to subtract (offset) the bottom by 0.5 volts (0 psi = 0.5 volts).

http://www.zenith.aero/forum/topics/swift-solid-state-oil-pressure-sensor

https://www.ebay.com/itm/Pressure-transducer-or-sender-Stainless-Steel-for-oil-fuel-air-water-Multichoice/272759060859?hash=item3f81b4f97b:m:mTKFrDgAsPLl-bZmKbUTKgQ

When searching note that oil pressure switches are often called sensors too.

Finn

On 11/15/2019 7:36 AM, Bobby J. Hughes bhughes@qnsi.net wrote:

Thermal pellet and carb jets with racing beat race regulator. Idle at 28 warm and 88-92 psi at 4800-7000 rpm.??

Bobby??

Sent from my iPhone

On Nov 15, 2019, at 2:43 AM, Matt Boiteau mattboiteau@gmail.com <flyrotary@lancaironline.net> wrote:

???

I installed an RX7 rear regulator and shimmed the front reg with 2 washers. Also installed thermal pellet and weber jets in the e-shaft. Average around 110-115psi during cruise, so I went with an 150psi sensor.

https://www.atkinsrotary.com/store/Competition-Eccentric-Shaft-Oil-and-Weber-Jet-Kit-ARE103.html
https://www.atkinsrotary.com/store/79-11-Rx7-and-Rx8-Increased-Oil-Pressure-Kit-ARE401.html
https://www.atkinsrotary.com/store/86-11-Rx7-and-Rx8-Atkins-Thermal-Pellet-ARE50.html?category_id=1275

- Matt Boiteau

On 2019-11-14 11:53:30 PM, Neil Unger 12348ung@gmail.com <flyrotary@lancaironline.net> wrote:

Fin,?? My renesis starts cold at 150 PSI.?? I let it idle at 2200 rpm
until after a few minutes it settles to 80 psi (plus).

Neil.

On 11/15/2019 10:45 AM, Finn Lassen finn.lassen@verizon.net wrote:
> I'm starting to look at engine monitor sensors for my RV-4.
>
> In his Renesis report, Tracy mentioned 100 psi oil pressures. Not
> clear if they dropped after the engine got some hours on it.
>
> What kind of oil pressures are you seeing?
>
> Should I go with a 150 psi or a 100 psi pressure sensor?
>
> Finn
>
>
> --
> Homepage:?? http://www.flyrotary.com/
> Archive and UnSub:
> http://mail.lancaironline.net:81/lists/flyrotary/List.html

--
Homepage: http://www.flyrotary.com/
Archive and UnSub: http://mail.lancaironline.net:81/lists/flyrotary/List.html