Mailing List flyrotary@lancaironline.net Message #64460
From: Bobby J. Hughes bhughes@qnsi.net <flyrotary@lancaironline.net>
Subject: RE: [FlyRotary] Re: 1mm thrust washer
Date: Mon, 12 Nov 2018 07:10:38 -0600
To: Rotary motors in aircraft <flyrotary@lancaironline.net>

Neil,

 

Looking good. The cup ID may need to be a few thousands over 52mm so not sure if there’s room for a mounting spigot. Depending on material thickness,  the cup will fully enclose one of the 2MM bearings and part of the 3.5mm thrust washer. Possibly add oil path grooves to the front and rear of the cup at 45 degree clocking. Depending on the material thickness the channels may need to be offset. Oil channels may not be necessary.

 

Too early for wine but well caffeinated!

 

Bobby

 

 

From: Rotary motors in aircraft [mailto:flyrotary@lancaironline.net]
Sent: Monday, November 12, 2018 2:26 AM
To: Rotary motors in aircraft
Subject: [FlyRotary] Re: 1mm thrust washer

 

Kelly,  I really should not draw freehand --- see if you can make sense of the scribble.  Neil.

 

On 11/12/2018 4:15 PM, Kelly Troyer keltro@gmail.com wrote:

Neil and All,

    Not sure I am visualizing the shape of the of the cup to encapsulate the 

1mm thrust washer but would certainly be a customer if Randy Kempf were

to gear up to produce them........How about sketch of the proposed shape

for those of us that are somewhat mechanically inept...........<:)

 

Kelly Troyer 

 

On Sun, Nov 11, 2018 at 6:52 PM Neil Unger 12348ung@gmail.com <flyrotary@lancaironline.net> wrote:

Bobby,

                        Sorry I misunderstood you.  By all means contact
Randy as he may be able to fit you in.  He has a complete reduction
drive of mine there to measure,  and certainly has the machinery to make
same.

Neil.


On 11/12/2018 7:41 AM, Bobby J. Hughes bhughes@qnsi.net wrote:
> Neil
>
> I was asking if Randy would consider making the 1mm washer mounting cup. I have a chip detector but removed it due to the 1mm washer / shaft wear creating fuzz every few hours and setting off an alert.  I also measure the gearbox oil temp output.
>
> Bobby
>
> Sent from my iPad
>
>> On Nov 11, 2018, at 3:15 PM, Neil Unger 12348ung@gmail.com <flyrotary@lancaironline.net> wrote:
>>
>> Bobby,
>>
>>                       Another way is what I did, was to put a temp sensor in the pSRU which will let you know if all is not well with elevated temps.  This is standard in heavy trucks,  One in the gear box, and one each in both diffs.  Simple and effective.
>>
>> Neil.
>>
>>
>>> On 11/12/2018 6:58 AM, Neil Unger wrote:
>>> Bobby,
>>>
>>>                       I put a magnet in the return line to catch any metal, but only got the "fuzz" you are talking about so simply removed it.
>>>
>>> Will discuss with Randy re stocking a chip detector.  That will be his commercial decision.
>>>
>>> Neil.
>>>
>>>
>>>> On 11/12/2018 3:29 AM, Bobby J. Hughes bhughes@qnsi.net wrote:
>>>> Neil,
>>>>
>>>> That should work. I believe Tracy has suggested the same solution. It would allow for replacing the 1mm washer if needed. I’m thinking aluminum instead of steel to minimize any wear on the washer outer edge if it rotated. I would like to start using my gearbox chip detector again. The 1mm washer shaft contact caused enough fuzz to activate it every few hours so I removed it. Would this be an item Randy Kempf would consider supplying? We need four in Austin TX and I’m sure others would retrofit if the part was available.  The cup OD would need to increased but I think we have plenty of room to accommodate modification.
>>>>
>>>> Thanks,
>>>> Bobby
>>>>
>>>> Sent from my iPad
>>>>
>>>>> On Nov 10, 2018, at 4:01 PM, Neil Unger 12348ung@gmail.com <flyrotary@lancaironline.net> wrote:
>>>>>
>>>>> Bobby,
>>>>>
>>>>>                     Tried my bearing blokes with no joy, over that size they are all 1.5mm.  There is another way however if there is room.  I suggest a small alloy (or steel) "cup" with mounting flanges like the washer you want, except in the middle the 1mm washer fits flat against the mounting plate as usual, and the cup then tapers upwards (after the 1mm thick retaining hole at the bottom ) and out slightly (for say another 3mm?) to prevent the 1mm thrust washer to "jump out of bed" and moving sideways. If it does move forward the taper will force it back into place when the load comes on again.  My $0.02 worth,
>>>>>
>>>>> Neil.


 

 

 

Subscribe (FEED) Subscribe (DIGEST) Subscribe (INDEX) Unsubscribe Mail to Listmaster