X-Virus-Scanned: clean according to Sophos on Logan.com Return-Path: Received: from imr-da03.mx.aol.com ([205.188.105.145] verified) by logan.com (CommuniGate Pro SMTP 5.4c3j) with ESMTP id 4983760 for flyrotary@lancaironline.net; Sat, 14 May 2011 19:31:51 -0400 Received-SPF: pass receiver=logan.com; client-ip=205.188.105.145; envelope-from=Bktrub@aol.com Received: from imo-da02.mx.aol.com (imo-da02.mx.aol.com [205.188.169.200]) by imr-da03.mx.aol.com (8.14.1/8.14.1) with ESMTP id p4ENVAVN026078 for ; Sat, 14 May 2011 19:31:10 -0400 Received: from Bktrub@aol.com by imo-da02.mx.aol.com (mail_out_v42.9.) id q.10c9.2640fc0 (56028) for ; Sat, 14 May 2011 19:31:05 -0400 (EDT) Received: from smtprly-dc02.mx.aol.com (smtprly-dc02.mx.aol.com [205.188.170.2]) by cia-md08.mx.aol.com (v129.10) with ESMTP id MAILCIAMD082-d2f34dcf10b7d3; Sat, 14 May 2011 19:31:05 -0400 Received: from webmail-d126 (webmail-d126.sim.aol.com [149.174.18.16]) by smtprly-dc02.mx.aol.com (v129.10) with ESMTP id MAILSMTPRLYDC022-d2f34dcf10b7d3; Sat, 14 May 2011 19:31:03 -0400 References: To: flyrotary@lancaironline.net Subject: Re: [FlyRotary] Re: Engine Tuning Date: Sat, 14 May 2011 19:31:03 -0400 X-AOL-IP: 50.46.100.112 In-Reply-To: X-MB-Message-Source: WebUI MIME-Version: 1.0 From: bktrub@aol.com X-MB-Message-Type: User Content-Type: multipart/alternative; boundary="--------MB_8CDE0A61FFCA571_1968_82A93_webmail-d126.sysops.aol.com" X-Mailer: AOL Webmail 33668-STANDARD Received: from 50.46.100.112 by webmail-d126.sysops.aol.com (149.174.18.16) with HTTP (WebMailUI); Sat, 14 May 2011 19:31:03 -0400 Message-Id: <8CDE0A61FF5814B-1968-5A901@webmail-d126.sysops.aol.com> X-Spam-Flag:NO X-AOL-SENDER: Bktrub@aol.com ----------MB_8CDE0A61FFCA571_1968_82A93_webmail-d126.sysops.aol.com Content-Transfer-Encoding: quoted-printable Content-Type: text/plain; charset="utf-8" I've got the crank angle sensor mounted on the crank pulley. I don't have= a scope, but even if I did, the problem only seems to happen at or near= WOT on climbout and in flight. I can run the engine wide open on the grou= nd and cannot get the backfiring that I get in the air. There must be enou= gh of a difference in engine loading to cause the problem, so I tend to th= ink it's not ignition, because if it were, I would be getting the same pro= blem on the ground.=20 Brian Trubee -----Original Message----- From: Mark Steitle To: Rotary motors in aircraft Sent: Sat, May 14, 2011 11:21 am Subject: [FlyRotary] Re: Engine Tuning Brian,=20 A number of us in the rotary group have had ignition issues with the EC-2.= I fought it for over a year, not sure if it was ignition, tuning, or a= little of both. It was running pretty good, then I had the brilliant ide= a to switch the 20B's CAS over to a Renesis style CAS (mounted on the cra= nk pulley). Apparently, the 20B's eccentric shaft has too much movement= to produce a good clean signal. Finally, in desperation, I switched back= to the original CAS and the high rpm tuning problem was magically cured.= Not sure what type CAS you're using, but you may want to put a scope on= the lead to see what is going on at high rpm. =20 Mark =20 On Sat, May 14, 2011 at 10:04 AM, wrote: I've had the same thought- that up at higher rpms I might be having some= sort of ignition problem. Adjusting the mixture does seem to mitigate it= somewhat, so that leads me to think that it is not an igntion problem. Al= so, it only seems to happen in flight, not on the ground, where the loads= are a little different. So, I still have questions about this, but I'm go= ing to approach this from the mixture angle. If I am having an igntion pro= blem, it's only happening at almost full throttle and in flight, so I'm sc= ratching my head trying to see how to test for this.=20 =20 Brian Trubee -----Original Message----- From: Steven W. Boese To: Rotary motors in aircraft Sent: Fri, May 13, 2011 10:28 pm Subject: [FlyRotary] Re: Engine Tuning Brian (and anyone else with more experience than me), =20 With my engine stand, primary injectors as small as 21 lb and secondary in= jectors from 30 to 50 lb have been used, with MAP up to 30 inches. Mixtur= es from lean misfire to rich misfire have been set with RPM up to 5800. = Although misfires can be induced with mixture, at no time was there anyth= ing that could be considered a backfire and certainly nothing like a grena= de. In flight, I have induced misfires with rich as well as lean mixtures= again with nothing like the results you describe. My plane=E2=80=99s muf= fler is a hollow tube about 6 inches in diameter 3 feet long with a slight= ly less than 2=E2=80=9D diameter outlet and two chambers inside separated= by a conical wall. This muffler would seem to be more of a bomb than a= grenade if a backfire were to happen. Doesn=E2=80=99t the fact that ther= e is a viable fuel-air mixture in the exhaust system seem to indicate that= the problem may be ignition rather than mixture? This is just a question= , not intended to be an answer. =20 Steve Boese RV6A 1986 13B NA RD1A EC2 =20 =20 =20 =20 From: Rotary motors in aircraft [mailto:flyrotary@lancaironline.net] On Be= half Of bktrub@aol.com Sent: Friday, May 13, 2011 3:35 PM To: Rotary motors in aircraft Subject: [FlyRotary] Engine Tuning =20 Since the weather has been cooperating lately, I've had the opportunity to= put a few more hours on the airplane. On the ground, I can go from an idl= e up to full throttle and the engine will be smooth. But when I take off,= it seems that as soon as I'm up a few hundred feet off the runway, I get= hellacious backfiring at full throttle. I can mitigate it a bit by thrott= ling back to about 5100 rpm, and turning the mixture knob to near full ric= h. It's getting to be a bit nerve wracking to take off thinking I've got= it smoothed out and then get a series of hand grenades going off under my= butt. I'm thinking that I'm still running too lean up at map address 106= or so. So, I go into the edit page and richen up the mixture around those= addresses. I think I'm creeping up on smooth full throttle running. =20 The good news is that my coolant runs at 175 degrees and oil at less- so= the cooling is more than effective, I just need to close up my air inlet= a bit or restrict the outflow. =20 Brian Trubee =3D=20 ----------MB_8CDE0A61FFCA571_1968_82A93_webmail-d126.sysops.aol.com Content-Transfer-Encoding: quoted-printable Content-Type: text/html; charset="utf-8"
I've got the crank angle sensor mounted on the crank pulley. I don't= have a scope, but even if I did, the problem only seems to happen at or= near WOT on climbout and in flight. I can run the engine wide open on the= ground and cannot get the backfiring that I get in the air. There must be= enough of a difference in engine loading to cause the problem, so I tend= to think it's not ignition, because if it were, I would be getting the sa= me problem on the ground.
 
 
 
Brian Trubee



-----Original Message-----
From: Mark Steitle <msteitle@gmail.com>
To: Rotary motors in aircraft <flyrotary@lancaironline.net>
Sent: Sat, May 14, 2011 11:21 am
Subject: [FlyRotary] Re: Engine Tuning

Brian, 

A number of us in the rotary group have had ignition issues with the= EC-2.  I fought it for over a year, not sure if it was ignition, tun= ing, or a little of both.  It was running pretty good, then I had the= brilliant idea to  switch the 20B's CAS over to a Renesis style CAS= (mounted on the crank pulley).  Apparently, the 20B's eccentric shaf= t has too much movement to produce a good clean signal.  Finally, in= desperation, I switched back to the original CAS and the high rpm tuning= problem was magically cured.  Not sure what type CAS you're using,= but you may want to put a scope on the lead to see what is going on at hi= gh rpm.  

Mark   

On Sat, May 14, 2011 at 10:04 AM, <bktrub@aol.com> wrote= :
I've had the same thought- that up at higher rpms I might be having= some sort of ignition problem.  Adjusting the mixture does seem to= mitigate it somewhat, so that leads me to think that it is not an igntion= problem. Also, it only seems to happen in flight, not on the ground, wher= e the loads are a little different. So, I still have questions about this,= but I'm going to approach this from the mixture angle. If I am having an= igntion problem, it's only happening at almost full throttle and in fligh= t, so I'm scratching my head trying to see how to test for this.
 
Brian Trubee



-----Original Message-----
From: Steven W. Boese <SBoese@uwyo.e= du>
To: Rotary motors in aircraft <flyrotary@lancaironline.net>
Sent: Fri, May 13, 2011 10:28 pm
Subject: [FlyRotary] Re: Engine Tuning

Brian (and anyone else= with more experience than me),
 
With my engine stand,= primary injectors as small as 21 lb and secondary injectors from 30 to 50= lb have been used, with MAP up to 30 inches.  Mixtures from lean mis= fire to rich misfire have been set with RPM up to 5800.  Although mis= fires can be induced with mixture, at no time was there anything that coul= d be considered a backfire and certainly nothing like a grenade.  In= flight, I have induced misfires with rich as well as lean mixtures again= with nothing like the results you describe.  My plane=E2=80=99s muff= ler is a hollow tube about 6 inches in diameter 3 feet long with a slightl= y less than 2=E2=80=9D diameter outlet and two chambers inside separated= by a conical wall.  This muffler would seem to be more of a bomb tha= n a grenade if a backfire were to happen.  Doesn=E2=80=99t the fact= that there is a viable fuel-air mixture in the exhaust system seem to ind= icate that the problem may be ignition rather than mixture?  This is= just a question, not intended to be an answer.
   &nbs= p;            =             &n= bsp;           &nbs= p;            =             =
Steve Boese
RV6A 1986 13B NA RD1A= EC2
&nb= sp;
 
    
&nb= sp;
From:= Rotary motors in aircraft [mailto:flyrotary@lancaironline.net]= On Behalf Of bktrub@aol.com<= br> Sent: Friday, May 13, 2011 3:35 PM
To: Rotary motors in aircraft
Subject: [FlyRotary] Engine Tuning
 

Since the weather has been cooperating lately, I've had the opportunity to= put a few more hours on the airplane. On the ground, I can go from an idl= e up to full throttle and the engine will be smooth. But when I take off,= it seems that as soon as I'm up a few hundred feet off the runway, I get= hellacious backfiring at full throttle. I can mitigate it a bit by thrott= ling back to about 5100 rpm, and turning the mixture knob to near full ric= h. It's getting to be a bit nerve wracking to take off thinking I've got= it smoothed out and then get a series of hand grenades going off under my= butt. I'm thinking that I'm still running too lean up at map address 106= or so. So, I go into the edit page and richen up the mixture around those= addresses. I think I'm creeping up on smooth full throttle running.
 = ;
The= good news is that my coolant runs at 175 degrees and oil at less- so the= cooling is more than effective, I just need to close up my air inlet a bi= t or restrict the outflow.
 = ;
Brian= Trubee
=3D

----------MB_8CDE0A61FFCA571_1968_82A93_webmail-d126.sysops.aol.com--