Dennis,
I'll
try and give you a more "detailed" review of you analysis and
approach in a short while (I have to dig up a drawing of the Renesis 4 port
intake to look at). However, I seem to recall that there is a valve in
the air passages of the intake that rotates open or closed depending of some
engine load variables. IF my memory is correct, this value in effect
halves (or doubles depending on which runner you are using for reference) the
distance the pulse has to travel from port of one rotor to port of the second
rotor. At the right rpm range the value closes forcing the pulse to
travel the shorter distance (or else it opens at the lower RPM range to make
the pulse travel a longer circuit – or vice versa – I have to look and see if
the Renesis even has such a valve – the older N/A 13Bs did have the value in
order to change the effective length of the intake runners.
I
can not tell from my hasty look at your e mails whether you took that factor
(the valve changing the effective length of the runner) into
consideration or indeed, if the Renesis even has one. ?
Will
get back to you shortly
Ed
From: Rotary motors in
aircraft [mailto:flyrotary@lancaironline.net]
On Behalf Of Dennis Haverlah
Sent: Thursday, January 01, 2009 11:59 AM
To: Rotary motors in aircraft
Subject: [FlyRotary] Re: Activity......
OK - I'll try to
stirrup some reflective comment on the list.
I'm in the middle of trying to design a new intake for my RX-8 Renesis powered
RV-7A
I've been reading the tuned intake discussion posts from 2004 and 2005.
FAW theory etc. I've tried
to apply the theories to the Mazda RX-8 4 port intake to see how it works
and make sure it
agreed with the theories. No Luck!!?
My measurements of the cast aluminum intake show primary runners are 12.5 in.
long + 2.5 inch to the center of the chamber
where the intake runners from rotor 1 interact with rotor 2's intake
runners. Add 3 inches at the other end ( engine flange) for the distance
from the
manifold flange to the center of the intake at the rotor face and the total
intake is 18.0 inches. The secondaries are 1/2 inch longer at 18.5
inches.
It appears they are using the FAW wave created as Rotor #1 intake opens to
travel through the intake tubes to Rotor #2. Total distance from
rotor
#1 to rotor #2 is 36 in. for primary runners and 37 in. for secondary runners.
Ed's post of Aug. 26,04 indicated a "E" shaft rotation of 93 deg.
between Rotor #1 opening and Rotor #2 closing. I measured the angle on an
old engine and agree.
The pulse from rotor #1 needs some opening to exit and at rotor #2 you must
have some opening to enter the rotor. I'll guess this is a total of 10
deg. Hence we have about 83 deg of "E" shaft rotation
time for the pulse to travel from rotor #1 to rotor #2.
I want to design my intake for max. HP at 6750 rpm. 6750/60 = 112.5 rps;
1/112.5 = 0.008888rev/sec or for 360 deg rotation of the "E" shaft it
takes 8.888ms.
The time for 83 deg of "E" shaft rotation would be
8.888ms*83deg/360deg = 2.05ms. (the time available for the pulse to travel from
rotor #1 to #2.)
speed of sound = 1100fps or 1.1f/ms*12 = 13.2 in/ms. So 13.2in/ms *
2.05 ms = 26.4 inch from rotor #1 to #2. My problem is this is already 5
in./ intake shorter than the RX-8 4 port intake. If I assume their
intake is designed for 8500 rpm the calculation indicates a runner length of 21.3
inches is needed between rotor
31 and #2. I measured the RX-8 cast al. intake to be 18 in * 2 = 36 in
.
To me it appears I do not understand how the RX-8 intake really works!!
Anyone have any ideas or find an error with the logic?
Going FAW crazy!!
Dennis H.
__________ Information from ESET NOD32 Antivirus, version of virus signature
database 3267 (20080714) __________
The message was checked by ESET NOD32 Antivirus.
http://www.eset.com