|
|
Ed,
Assuming you really don't need a gallon, how about if I send you a pint
from the upholstery shop? I need to stop in tomorrow to see if my
seats are finished anyway. I think he will just give me a little from
his 5 gallon can. (I also maintain his web site.) If I can get it you
can send me your address. The best place to purchase it is an
upholstery supply house.
Bob W. (upholstery shop - http://www.bearnutupholstery.com)
On Thu, 5 Jan 2006 22:57:42 -0500
"Ed Anderson" <eanderson@carolina.rr.com> wrote:
> Hey, where were you when I was doing my upholstery {:>). The 3M stuff
> just doesn't hold to vinyl or foam very well. Yes, I would be very
> interested in the exact name. I would think some of the auto paint shop
> might carry something like that. I prefer the brush on form as spray would
> just get it everywhere (if you are as messy as I am with a spray gun).
>
> Thanks, Bob
>
> Ed
>
> ----- Original Message -----
> From: "Bob White" <rlwhite@comcast.net>
> To: "Rotary motors in aircraft" <flyrotary@lancaironline.net>
> Sent: Thursday, January 05, 2006 9:48 PM
> Subject: [FlyRotary] Re: A good? flight.
>
>
> > Hi Ed,
> >
> > There is a contact cement made for vinyl tops on cars that works way
> > better than the normal 3M contact cement. It's Landau Top
> > Cement and is available in a spray can. If you're interested I can get
> > the exact name and manufacturer tomorrow. It's also available in liquid
> > form if you want to brush it on or spray it with your own spray gun but
> > I think the smallest size is 1 gallon in that form.
> >
> > I've used it to attach vinyl to aluminum on top of my instrument panel,
> > attach the rubber grip to my control stick, and attach a strip of foam
> > to seal the hinge crack in the wood hanger door.
> >
> > Bob W. (Tip from my buddy at the upholstery shop)
> >
> >
> >
> > On Thu, 5 Jan 2006 13:04:35 -0500
> > "Ed Anderson" <eanderson@carolina.rr.com> wrote:
> >
> >
> >> Finally the dust and straw stopped flying and I had a soft cloth to wipe
> >> off the canopy. So continued the flight. Then a few minutes later I
> >> notice the vinyl cloth I had covering the top of the instrument panel was
> >> starting to balloon up (apparently after 7 years the glue had dried out)
> >> due to air apparently leaking in from the front of the canopy. Put a
> >> water bottle and few other things on top and that held it down.
> >
> >>
> >> Ed
> >>
> >> Ed Anderson
> >> Rv-6A N494BW Rotary Powered
> >> Matthews, NC
> >> eanderson@carolina.rr.com
> >>
> >
> > --
> > http://www.bob-white.com
> > N93BD - Rotary Powered BD-4 (Projected engine start - maybe next week)
> > Custom Cables for your rotary installation -
> > http://www.roblinphoto.com/shop/
> >
> > --
> > Homepage: http://www.flyrotary.com/
> > Archive and UnSub: http://mail.lancaironline.net/lists/flyrotary/
> >
>
>
>
> --
> Homepage: http://www.flyrotary.com/
> Archive and UnSub: http://mail.lancaironline.net/lists/flyrotary/
--
http://www.bob-white.com
N93BD - Rotary Powered BD-4 (Projected engine start - maybe next week)
Custom Cables for your rotary installation -
http://www.roblinphoto.com/shop/
|
|