|
|
Hi George,
I haven't found anywhere on the web that there are the kind of cross
references like I can find for GM. Even then it was fairly difficult
to figure out what the commercial part was for the LS1 truck coils.
If I can get any kind of reference on it, I can try to track it down.
BTW, I received the 2005 Corvette injectors that are supposed to have
a hotter spark. They can use the same connector the LS1 trucks use.
The inside of the connector cavity is different, so I'm not sure the
connector used on the Corvette is exaclty the same. I'll have to check
that out.
Bob W.
On Mon, 5 Dec 2005 08:24:15 +1000
"george lendich" <lendich@optusnet.com.au> wrote:
> Thanks Bob,
> I realised my mistake just after I hit the send button.
> Do you think you could track it down from your sources. The RX8 fitting is,
> Kelly advises, the same as the 1999-2002 Mazda Protege and the1993-95 RX7.
> I would say that a lot of people might use the RX8 timing wheel, if they
> could source everything.
> George ( down under)
>
> > Hi George,
> >
> > I think you meant Bob White so I'll respond. :) I don't recognize the
> > connector from the picture.
> >
> > Bob W.
> >
> >
> > On Sun, 4 Dec 2005 17:48:42 +1000
> > "george lendich" <lendich@optusnet.com.au> wrote:
> >
> > > Kelly,
> > > I was hoping to buy one ( connector) off the shelf, without having to
> chase around wreckers for one.
> > > I wonder if Bill White can source these - Bill are you there?
> > > George ( down under)
> > > George,
> > > Do you mean the 2 pin connector of the sensor........That is the
> > > connector (along with a pigtail of wire for splicing) from the donor
> > > auto that I suggested.......
> > >
> > > --
> > > Kelly Troyer
> > > Dyke Delta/13B/RD1C/EC2
> > >
> > >
> > >
> > >
> > >
> > >
> > > -------------- Original message from "george lendich"
> <lendich@optusnet.com.au>: --------------
> > >
> > >
> > > Kelly,
> > > What I really need is the connector for the 2 pin plug - any ideas.
> > > George ( down under)
> > > Ken,
> > > This is what you are looking for !!
> > > --
> > > Kelly Troyer
> > > Dyke Delta/13B/RD1C/EC2
> > >
> > >
> > >
> > >
> > >
> > >
> > > -------------- Original message from keltro@att.net (Kelly
> Troyer): --------------
> > >
> > >
> > > Ken,
> > > Hit the junkyards........1999-2002 Mazda Protege "Camshaft
> Sensor"
> > > is the same part number as the 1993-95 RX7 eccentric shaft
> sensor....
> > > Rock Auto price had best price of $81.00 that I found.......Get
> the
> > > connector from the donor car harness with the sensor !!
> > > --
> > > Kelly Troyer
> > > Dyke Delta/13B/RD1C/EC2
> > >
> > >
> > >
> > >
> > >
> > >
> > > -------------- Original message from
> kenpowell@comcast.net: --------------
> > >
> > >
> > > Kelly,
> > > I need one of these too plus the pickup. I'll be really
> interested in what you find.
> > >
> > > Ken Powell
> > > Bryant, Arkansas
> > > 501-847-4721
> > > C150 / RV-4 under construction
> > >
> > >
> > >
> > >
> >
> > --------------------------------------------------------------------------
> > >
> > >
> > > --
> > > Homepage: http://www.flyrotary.com/
> > > Archive and UnSub:
> http://mail.lancaironline.net/lists/flyrotary/
> > >
> >
> >
> > --
> > http://www.bob-white.com
> > N93BD - Rotary Powered BD-4 (Projected engine start - maybe next week)
> > Custom Cables for your rotary installation -
> > http://www.roblinphoto.com/shop/
> >
> > --
> > Homepage: http://www.flyrotary.com/
> > Archive and UnSub: http://mail.lancaironline.net/lists/flyrotary/
> >
>
>
>
> --
> Homepage: http://www.flyrotary.com/
> Archive and UnSub: http://mail.lancaironline.net/lists/flyrotary/
--
http://www.bob-white.com
N93BD - Rotary Powered BD-4 (Projected engine start - maybe next week)
Custom Cables for your rotary installation -
http://www.roblinphoto.com/shop/
|
|