Received-SPF: none
 receiver=logan.com; client-ip=211.29.132.182; envelope-from=lendich@optusnet.com.au
Message-ID: <001b01c5b844$9338b060$1fe8683a@george>
From: "George Lendich" <lendich@optusnet.com.au>
To: "Rotary motors in aircraft" <flyrotary@lancaironline.net>
References: <list-719859@logan.com>
Subject: Re: [FlyRotary] Re: Ignition Coil Connectors
Date: Tue, 13 Sep 2005 19:21:51 +1000
MIME-Version: 1.0
Content-Type: text/plain;
	charset="iso-8859-1"
Content-Transfer-Encoding: 7bit

Bob
I found it but can't find the products - is there a year make model that I
have to enter in the catalogue?
George

> Again, Joe didn't write that.  I was addressing the next part of the
> message to Joe.  Sorry for causing all the confusion.
>
> GM Parts Direct  http://www.gmpartsdirect.com/
>
> Bob W.
>
> On Tue, 13 Sep 2005 11:00:51 +1000
> "George Lendich" <lendich@optusnet.com.au> wrote:
>
> > Joe,
> > Being in Australia makes it that much harder to source specific
> > things. Could you direct me to an email address for GM Parts Direct
please
> > Joe.
> > TIA
> > George ( down under)
> >
> > > Was the connector you thought was correct the same one that's used on
> > > the D580?  If not, where did you find them and do they have one that
> > > will fit? I hope you didn't have to pay $25 a piece for them!
> > >
> > > GM Parts direct sells the D581 coils for $25 and the D580 for $32.
> > >
> > >
> > > Joe,
> > >
> > > I've updated the wiki to make it clear that the D580 connector doesn't
> > > fit the D581 coil.
> > >
> > > Bob W.
> > >
> > >
> > >
> > > On Mon, 12 Sep 2005 07:30:17 -0500
> > > "Mark R Steitle" <mark.steitle@austin.utexas.edu> wrote:
> > >
> > > > Joe & Dale,
> > > >
> > > > Just a bit of caution here.  I'm using the D581 (Chevy pickkup
version)
> > > > coils.  I ordered what looked to be the correct connectors, only to
find
> > > > out that they had an indexing lug that prevented them from mating
with
> > > > the coils.  I trimmed the indexing lug off and used them anyway as
there
> > > > is a lock that prevents them from being inserted 180* out.  Just be
sure
> > > > you check it very carefully.  Connectors cost as much as the coils.
Go
> > > > figure!  You can always do what Tracy did and solder wires to the
pins
> > > > on the coils, then pot the plug hole.  Then use one large connector
on
> > > > the whole bundle.
> > > >
> > > >
> > > >
> > > > Mark S.
> > > >
> > > >
> > >
> > >
> > > --
> > > http://www.bob-white.com
> > > N93BD - Rotary Powered BD-4 (real soon)
> > > Prewired EC2 Cables - http://www.roblinphoto.com/shop/
> > >
> > > --
> > > Homepage:  http://www.flyrotary.com/
> > > Archive and UnSub:   http://mail.lancaironline.net/lists/flyrotary/
> >
> >
> >
> > --
> > Homepage:  http://www.flyrotary.com/
> > Archive and UnSub:   http://mail.lancaironline.net/lists/flyrotary/
> >
> >
>
>
> --
> http://www.bob-white.com
> N93BD - Rotary Powered BD-4 (real soon)
> Prewired EC2 Cables - http://www.roblinphoto.com/shop/
>
> --
> Homepage:  http://www.flyrotary.com/
> Archive and UnSub:   http://mail.lancaironline.net/lists/flyrotary/
>